Normas que usa este programa
Normas (79)EN 806-1 — Water installations inside buildings: General (2000 + A1:2001)EN 806-2 — Design (2005)EN 806-3 — Pipe sizing, simplified method (2006)EN 806-4 — Installation (2010)EN 806-5 — Operation and maintenance (2012)CEN/TR 16355 — Prevention of Legionella growth in drinking water installations (2012)EN 12831-3 — Domestic hot water systems heat load and characterisation of needs (2017)EN ISO 12241 — Thermal insulation for building equipment, calculation rules (1998 (curr…
+71 másVer menos
EN 1717 — Protection against pollution of potable water by backflow (2000)EN 12729 — Controllable backflow preventer with reduced pressure zone (family B type A)…EN 14367 — Non-controllable backflow preventer with different pressure zones (family C …EN 14454 — Hose union vacuum breaker DN 15–DN 25 (family H type A)EN 13076 — Unrestricted air gap (family A type A)EN 1567 — Water pressure-reducing valvesEN 1489 — Pressure safety valves (2000)EN 12897 — Indirectly heated unvented storage water heaters (2016 + A1:2020)EN 12828 — Heating systems in buildings: design of water-based heating systems (2012 + …EN 13443-1 — Mechanical filters ≥ 80 µm to < 150 µm (2002 + A1:2007)EN 1057 — Seamless round copper tubes for water and gas (2006 + A1:2010)ISO 65 — Carbon steel tubes for screwing (medium series) (1981)DIN 1988-2 — Drinking water supply systems: materials, components, installationDIN 1988-3 — Drinking water supply systems: pipe sizing (1988-12)EN 12056-1 — Gravity drainage inside buildings: general and performance (2000)EN 12056-2 — Sanitary pipework, layout and calculation (2000)EN 12056-3 — Roof drainage, layout and calculation (2000)EN 12056-4 — Wastewater lifting plants, layout and calculation (2000)EN 12056-5 — Installation and testing, instructions for operation, maintenance and use …EN 12050-1 — Lifting plants for wastewater containing faecal matter (2001)EN 12380 — Air admittance valves for drainage systems (2002)EN 13564-1 — Anti-flooding devices for buildings: requirements (2002)EN 1825-2 — Grease separators: selection of nominal size, installation, operation (2002)EN 752 — Drain and sewer systems outside buildings (2017)EN 1610 — Construction and testing of drains and sewers (2015)EN 1329-1 — Plastics piping for soil and waste inside buildings: PVC-U (1999 (current 2…EN 1451-1 — Plastics piping for soil and waste inside buildings: PP (2017)EN 14366-1 — Laboratory measurement of noise from waste water installations (2023 (EN 1…EN 12354-5 (prEN 12354-5) — Building acoustics: sounds levels due to service equipment …EN 16941-1 — On-site non-potable water systems: rainwater (2018)EN 16941-2 — On-site non-potable water systems: treated greywater (2021)EN 12845 — Fixed firefighting systems, automatic sprinkler systems: design, installatio…EN 671-1 — Hose systems: hose reels with semi-rigid hose (2012)EN 671-2 — Hose systems: hose systems with lay-flat hose (2001)VdS CEA 4001 — Guidelines for sprinkler systems: planning and installation (2010-11 (fo…EN 1366-3 — Fire resistance tests for service installations: penetration seals (2009 (c…EN 13501-2 — Fire classification from resistance tests (2007 + A1:2009 (folder: SR EN 1…ISO 834-1 — Fire-resistance tests: general requirements (1999)ISO 10295-1 — Fire testing of service installations: penetration seals (2007)EN 1775 — Gas pipework for buildings, maximum operating pressure ≤ 5 bar (2007)EN 15001-1 — Gas installation pipework above 0.5 bar (industrial) / above 5 bar (2009)EN 17210 — Accessibility and usability of the built environment: functional requirement…CEN/TR 17621 — Accessibility: technical performance criteria (2021)EN 12976-1 — Thermal solar systems: factory-made systems (Not sure (current 2017))EN 12977-1 (and -5) — Thermal solar systems: custom-built systems (2012)EN 1991-1-1 — Densities, self-weight, imposed loads (2002)EN 1991-1-4 — Wind actions (2005 + A1:2010)EN 1998-1 — Earthquake resistance, general rules (2004 + A1:2013)EN 1993-1-1 — Steel structures, general rules (2005 + AC:2009)EN 1993-1-8 — Design of joints (2005 + AC:2009)EN 1992-4 — Design of fastenings for use in concrete (2018)EN 1992-1-1 — Concrete structures, general rules (2004 + A1:2014)EN 206 — Concrete (2013 + A2:2021)EOTA TR 055 — Design of fastenings on the basis of EOTA-format ETAs (2016, amended 2018)ETAG 001 Annex C — Metal anchors for use in concrete, design methods (2010)EAD 330232-01-0601 / -02-0601 — Mechanical fasteners for use in concrete (2016 / 2021)EAD 330499-02-0601 — Bonded fasteners for use in concrete (2022)ETA-20/0046 — ADIT THE / TFE / TXE concrete screws (2026, version 8)ETA-12/0397 — ADIT MTP / MTP-G / MTP-X / MTP-A4 wedge anchors (2025, version 7)ETA-14/0068 and ETA-14/0135 — ADIT HEHO / HECLO / HE-HC anchors (2025 v6 / 2026 v4)ETA-15/0912 — ADIT HC anchor for hollow-core slabsETA-20/0494 — THE / TFE / TFF screws in hollow-core slabsETA-15/0145, ETA-18/1108 — MTP-A4; SLPT / SLPCETA-18/0797 — Chemfix CH 200 bonded anchor (2018)ETA-19/0705 — Chemfix 100 / 600 bonded anchor (2022 (r3))ISO 898-1 — Carbon and alloy steel fasteners: property classes (2013)ISO 3506-1 — Stainless steel fasteners (2020)ISO 7089 / DIN 125 — Plain washers (2000 / —)DIN 9021 — Wide plain washersISO 4032 / DIN 934 — Hexagon nuts (1999 / 1987)DIN 985 — Prevailing-torque nylon-insert nuts
¿Preguntas sobre este programa? Pregunta al agente de IA (el botón ✨ abajo a la derecha).
